Author: hqt

What should be considered before assembly?

Before assembly, one thing in particular must be observed – cleanliness! Before you start installing your smart film tint for car, you should thoroughly clean your glass surfaces using a scraper and some glass cleaner.

This prevents the inclusion of dust and dirt and at the same time ensures a better hold of the sun protection film.

When installing outer foils, you should make sure that you do this on a day with as little wind as possible in good weather. This makes assembly much easier and reduces the risk of inclusions.

You should also make sure that you really measure the glass surfaces correctly. The glass surfaces extend a few mm into the frame, which must also be taken into account.

What steps should I follow when installing smart film tint for car?

First of all, you should measure the panes on which you want to stick sun protection films to make sure that you are ordering the right cuts or the right number of linear meters.

If you then want to mount your sun protection film, you first remove (if available) the glazing beads or the rubber seal in order to later ensure the edge connection of the film. A screwdriver is a useful tool for this.

During the installation itself, the first step – as mentioned above – is to thoroughly clean the entire glass surface. You have stubborn dirt on your glasses. We recommend cleaning the window glass with a glass scraper.

Hold your blank to check whether smart film tint for car really fits

If everything fits, spray the glass surface thoroughly with a mixture of water and assembly concentrate (60:1). The pane can be really wet, because you will later squeeze the water out with a squeezer under the film and it will make it easier for you to install the sun protection film.

Then carefully remove the protective film from the back of the film without touching the adhesive. It is helpful if you also spray your fingers with the mixture of water and assembly concentrate to avoid fingerprints on the sun protection film.

Moisten the adhesive surface of the foil with the assembly concentrate

A little tip: Only remove the smart film tint for car at the top and attach the upper part to the glass surface and then go down step by step.

When the sun protection film covers the entire surface, use the squeezer to squeeze out the excess water under the film with a little pressure. For the edge area, use the squeegee to get into every corner.

It’s best to start in the middle and squeeze from their first up and then down. It is important to always squeeze from top to bottom or from bottom to top, never from right to left. This is how you avoid streaks.

If you can no longer see any bubbles or water deposits behind your sun protection smart film tint for car. You can carefully dry the edge with a clean cloth.

Finally, ensure that the film is attached to the edge of the window frame by either reinstalling the glazing beads or the rubber seal, or – if these are not available – seal the edge area of ​​the sun protection film and the window frame with the help of special silicone.

Can I install sun protection films alone?

We always recommend at least two people to install the film. In principle, assembly can also be done alone, but especially with more complicated steps, such as removing the protective film of the sun protection smart film tint for car and spraying the adhesive surface at the same time, a third or fourth hand makes the work much easier.

Which tool do I need?

Tools and installation utensils that you need to install your sun protection film are:

• 2 pump sprayers (one for the glass cleaner, one for the assembly concentrate)
• 1x assembly concentrate
• 1x glass cleaner
• Glass scraper
• If necessary, replacement blades
• Window wiper
• Puller
• Cutter (to cut the foil if necessary)
• If necessary, replacement blades
• Squeezer
• Squeegee
• If necessary, edge sharpened

After spraying the pane liberally with the glass cleaner, you should put a smart film tint for car on the pane, which will remain attached by the glass cleaner. The adhesive is softened by the plastic foil.

Approx. 30 minutes later you can remove the window film or sun protection film in one piece.

What do I do with glue residue?

To remove the released adhesive, first spray undiluted glass cleaner onto the glass surface. This softens the glue after about 15 minutes. Now you can use a glass scraper to remove the adhesive from the pane.

Caution is required with glass (toughened safety glass)! Since this type of glass has a soft surface, it is very easy to scratch when using glass scrapers.

If the glue does not come off smoothly from smart film tint for car, we recommend rubbing a little spirit on the glass surfaces. After a few minutes, the adhesive residue will turn gray. Now you can easily remove the remains with the help of a glass scraper or a spirit cloth.

Can a window film be removed without leaving any residue?

YES! The films can be removed from the pane without leaving any residue, provided you have the right tool and follow the instructions for removal.

However, it should be noted that very old or cheap foils behave differently when dismantled. It can happen that the film tears into individual pieces – this makes dismantling extremely difficult.

Which tool do I need for this?

In principle, you do not need any special tools to dismantle foils.

You only need a glass cleaner and a glass scraper to remove the smart film tint for car. You can use a little spirit for stubborn glue residue.

We recommend that you use glass cleaner, as it does what it promises. It cleans the window surface perfectly and is also ideal for film installation.

We would like to advise you to avoid using aggressive solvents. These only emit fumes that can harm your health.

What is a privacy film?

A smart film switchable is a self-adhesive sticker made from a high-performance film (glass decoration film) with an elegant sandblasting effect, suitable for smooth glass surfaces. Visually comparable to etched glass or frosted glass, the privacy film is opaque and yet 70% translucent.

Daylight is therefore hardly lost. The privacy film is contour cut with no background and comes ready to install with transfer paper. Where the motif/text is cut out negatively, the glass surface remains visible.

Is the privacy film opaque?

Yes, the privacy film is opaque. In the dark and in a bright room, you will be able to see outlines from the outside, but no people or objects. Please note that with privacy smart film switchable, the motifs or texts are cut out of the film. In these places, the privacy screen is of course not opaque. We recommend selecting the right motif according to the desired effect.

For which glass surfaces is the privacy film suitable?

The glass surface should be smooth – i.e. no structured glass. If the background consists of a milky glass, you will probably only recognize the privacy screen slightly or very discreetly.

The privacy film can be used indoors, outdoors and in wet areas without any problems, i.e. also in the bathroom or wellness area.

Is the smart film switchable glued from the inside or from the outside?

The privacy film can be stuck on from the inside as well as from the outside. The foil has the same effect on both sides.  For shop windows, we recommend pasting the outside to avoid glass reflections.

How is the privacy film installed or removed?

With the help of our assembly instructions, the privacy film can be easily assembled and easily removed even after a longer period of time – by heating it with a hair dryer. Please be sure to follow the appropriate assembly instructions included in each package.

How long does the smart film switchable last?

The film manufacturer gives a guarantee of up to 7 years on the privacy film (glass decoration film) outdoors. Experience has shown that the durability is significantly higher. It is best for both short-term and long-term use.

How long can I store the privacy film?

If storage of this film is necessary, the sticker should be stored in a dry, cool and dark place and processed within four to six weeks of the delivery date.

How do you clean a pane of glass that has been covered with privacy film?

The glass surface comes with our smart film switchable. It can be cleaned as normal. We recommend e.g. B. Chamois leather, lint-free cotton cloths, normal glass cleaners (no scouring agents) – just no rough and pointed objects such as blades or scouring pads.

I have stains in my privacy film. What can I do?

Due to wet bonding, the adhesive can temporarily turn white/yellowish. After complete drying, these “clouds” disappear completely, usually after 1-3 days. Depending on the humidity and temperature, this can take up to 14 days in individual cases.

Just like all other window protection and safety films, the privacy films are made of polyester film (PET). Due to their opaque properties, Film-Pal smart film switchable prevents prying eyes from entering private and business premises.

Despite this property, they are translucent and allow light into the premises.

Is a sun protection film also a privacy film?

It always depends on the light difference between the rooms.

If it is brighter outside than inside, dark sun protection films with a reflective exterior (with a high degree of reflection) provide privacy protection. But is it darker inside than outside?

then the effect reverses you and you can look into the room again (trick mirror effect). With smart film switchable such as the white matt Classic from Film-Pal, the lighting conditions are not important. They guarantee privacy regardless of these factors.

How does privacy film hold up?

Like all other films from WGLASS, privacy films are provided with a special acrylate adhesive. Our privacy films are also processed with moisture, as wet.

In this state, the foils can be moved on the glass pane until the mounting liquid has been squeezed out from under the foil. After that, the privacy film holds just as reliably as all other smart film switchable from WGLASS. It is best to connect the foil to the edge area of ​​the pane.

There are one or two ways to do this. If there are removable glazing beads or rubber seals, the film underneath can be processed indoors. These are not available or outdoors in general, the film should be sealed with neutrally cross-linked silicone.

How do you stick privacy film?

Like other window films, privacy films are glued to flat/smooth glass surfaces, since processing on structured glazing is only possible with limitations in processing and adhesive strength.

First you clean the glass surface to be coated with glass cleaner to avoid inclusions. Then pull the protective film off the previously cut smart film switchable and then wet the adhesive surface of the film with assembly fluid (mixture of assembly concentrate and water 1:60).

Once the privacy film is positioned correctly, you can start squeezing out the liquid from under the film to fix it on the pane. Finally, dry the edge area. Lint-free paper towels that do not shed fibers are best suited for this. You can buy best privacy films from us.

How do privacy films differ from each other?

Privacy films are available in different colors and types. The foils differ in their different transmission values, their reflection values ​​and the colors of the foils.

Smart film switchable is available in matt white, matt silver or opaque black and opaque white. For outdoor use, we also offer the opaque variants in silver-black and silver-white. You can also use spy mirror film as a privacy film, which is completely opaque under the right lighting conditions. However, note the previously described trick mirror effect.

Firstly, smart film, just like smart glass, performs the function of intelligent glass dimming to achieve 100% privacy. In opaque mode, glass uses to project images or videos.

The glass state can be changed from transparent to opaque at the touch of a button.

Smart film is a technological and modern tool: change, expand and delimit a fixed space whenever you want.

Smart film in the commercial sector 

Moreover, smart film is an easy way to ensure privacy while using the conference room. Also, very often, in the offices of managers there is a glass door and it is not entirely ethical and comfortable to conduct important negotiations with it.

PDLC films easily solve this problem As well as, it is the easiest way to ensure privacy during an important meeting.

There are three sizes of smart film

Web Width:

• 1200 mm
• 1500 mm
• 1800 mm

The length of the canvas can be any but not more than 4000 mm.

Any color scheme is available.

Installation on old glasses or windows is possible.

PDLC film is glued onto finished clear or frosted glass.

Frequently asked questions about smart film

• Does smart film block harmful UV rays?
  Yes, it blocks over 98% of harmful UV rays in both activated and inactive states.
• Is smart film energy efficient?
  Yes, smart film consumes 3 to 6 watts per square meter.
• How else can smart film be used?
  Smart film is very popular for projection screens, electronic blinds, and whiteboards and high-tech windows.
• How much does smart film cost?
  Each project with smart glass and smart film is special. We make your order according to individual sizes and criteria, so the price of smart film is always different.

Is it possible to install smart film on only half of the glass?
Yes, you can install our smart film on any part of the glass.

Is smart film cheaper than smart glass?
Yes, you pay only for the film itself, its application and connection.

What else needs for smart film to work?
Moreover, you will need electricity (220V) and the transformer that comes with the film.

Is it possible to project an image onto smart film?
Yes, smart film is ideal for use as an extremely high definition projection film. Eventually, we have many satisfied customers who use the glass facade of their store as a billboard.

Eventually, window tinting gives the car an attractive look and protects from the sun’s rays. Changes in traffic rules have seriously limited the possibilities of traditional methods. A modern, innovative approach comes to the rescue – electronic tinting using PDLC technology. Its features deserve the attention of motorists.

The essence of PDLC technology

Furthermore, Monochrome PDLC (LCD) technology develops by the South Korean company DM DISPLAY. It is a kind of electronic tinting based on the Smart-effect, which allows you to change the light transmission of glass. The PDLC technology considers being a close analogue of the American SPD technology.

In addition, the desired effect achieves by smart film containing a special layer. It contains a liquid-crystal substance between two polymer films. In the normal state, liquid crystals are randomly distributed over the material, which makes the layer as dense as possible and opaque to sunlight.

What happened when an electric voltage applies?

When voltages apply an electric field creates that gives the crystals a certain orientation. As well as, it freely moving between polymer films, In addition, they distribute in an orderly manner, due to which the density decreases and the light transmission of the layer increases, and hence the transparency of the entire glass.

 

Attention! With an increase in the strength of the smart film electric current, the degree of darkening of the glass increases. At the maximum electrical signal, it becomes almost black, and when it turns off, it becomes perfectly transparent.

Advantages and disadvantages of monochrome tinting

The following advantages of PDLC tinting stand out:

1. The ability to adjust the degree of transparency allows you to provide an optimal view of the road at different times of the day. The risk of creating an emergency reduces by limiting visibility through tinted glass at night.
2. Virtually complete UV protection. Subsequently, PDLC tinting is capable of absorbing over 90% of UV light.
3. Smart filmmaintains a comfortable temperature in the cabin much better, which allows you to save on air conditioning and heating. They keep warm in winter and cool in summer.
4. Even with maximum tinting, natural light penetrates well inside.
5. Almost instantaneous change in the degree of transparency of the glass.

It should be noted the presence of disadvantages of such tinting

1. High material and installation cost.
2. The need to attract specialists for installation.
3. Additional load on the battery.

Despite the high cost of smart film, their popularity is constantly growing. In addition, this is largely due to penalties for excessive tinting, and PDLC technology allows you to keep its degree within acceptable limits (light transmission is at least 75% for windshields).

PDLC Production technology

Secondly, monochrome PDLC tinting provides by “smart”, i.e. smart glass. It is made of two layers of ordinary automotive glass, between which a smart film places. Moreover, in it, a conductive liquid crystal substance places between two polymer films.

In addition, polymer films play the role of mechanical protection and electrical insulation. Special electrical outlets allow you to connect a smart film to a car battery, through which a voltage of 12 V is supplied to liquid crystals.

Differences between monochrome PDLC tinting and regular tinting

Moreover, smart film monochrome tinting technology PDLC – modern innovations for a comfortable ride Standard car window tinting involves sticking a dark polymer film on them. It can select by color and degree of transparency.

As well as, the main difference between such tinting and PDLC technology is the constancy of light transmission, which is set by the properties of the material and does not depend on external influences.

Regular tinting also has other disadvantages. The film can peel off the glass, which not only spoils the appearance, but interferes with the review. Located outside the glass, it can subject to various mechanical stresses.

Differences from other types of electro toning

Firstly, pdlc smart film is one of the best inventions to make best privacy. Its basis is a film containing a layer of rod-shaped particles fill with a non-conductive liquid. In the normal state, these particles locate close to each other, making it difficult for light to penetrate.

In this state, the light transmission capacity does not exceed 15%. When an electrical voltage applies, the particles orient in one direction and move away from each other.

Is pdlc smart film technology dependable?

Pdlc smart film technology considers more reliable. Such a film can glue to any car glass. At the same time, it has a very high mechanical strength.

The main disadvantages are: a higher price compared to PDLC and the lack of production in the Europe.  A well-known electronic tinting technology is Wigless. It provides for the installation of laminated smart glass. Smart film places between all layers. This increases the adjustment possibilities and achieves a blackout of up to 96%.

What are the advantages of smart film?

Such pdlc smart film creates a “thermos” effect, keeping the temperature in the cabin well. Almost 4 times more impact strength compared to conventional glass.

Main disadvantages: high cost and heavy weight. The latter circumstance has a particularly strong effect on the design of doors and windows.

The budget option for adjustable tinting is double glass. This technology provides for the installation of a system of two glasses, each of which has its own power window and its own guide elements. One of the glasses tints and the second is ordinary glass. Raising this or that glass, it is possible to provide transparency or darkening.

Important! In severe conditions, PDLC tinting looks preferable to other electric tinting.

Structure and principle of operation of PDLC film

Pdlc smart film works on PDLC technology. A liquid-crystal substance places between strong polymer films. When, an electric current applies the density of the crystals changes, which increases the light transmission capacity.

Such a film differs in that additional elements introduces into its composition that can play the role of a catalyst. They design to react to temperature. When a current passes through a substance, it heats, and the catalyst accelerates the process of changing transparency under the influence of a temperature background.

How Installing PDLC tint?

Pdlc smart film tinting can be done by replacing glass (ordinary glass with smart glass) or sticking an electro chromic film.

Installation of smart glass carries out in the following order:

1. Order smart glasses. They are made for a specific car. To do this, it is necessary to inform not only its model, but also the factory number of the glasses.
2. Dismantling the windshield and rear window. Dismantling the door frame and removing the side windows.
3. Installation of new smart glasses.

There is no need to remove the glass to stick the film

1. Glass surfaces being prepare. Removing old films, cleaning from dirt and dust.
2. Carefully apply a soapy solution to the entire surface of the glass. It should be evenly distribute over the entire area.
3. The film pasts. Smoothing is done with a rubber spatula, with smooth movements.
4. Special copper contacts bond to the liquid crystal layer using silver paste. Next, the contacts solder to the power supply and the controller.

The pdlc smart film tinting process can equip with a system for automatically adjusting the degree of transparency.

 It achieves in 2 ways: By introducing a special program into the on-board computer or by installing external light sensors.

The cost of pdlc smart film

Electronic tinting is a rather expensive procedure. The average cost of materials for its various types is:

1. P.D. _ the kit includes glasses, wires and a controller.
2. Double glass. The kit includes glass and electric motors.
3. .

The cost of tinting depends on the size of the glass and the class of the car. It should remember that the total area of ​​​​tinting varies significantly for different models.

Maintenance of PDLC tinted windows

Caring for PDLC glass is the same as caring for ordinary car windows. The pdlc smart film is also quite reliably protects by high-strength plastic. These materials well tolerate by frost, direct sunlight, temperature fluctuations, and moisture.

They can wash with cold and hot water. It allows using ordinary detergents use for cars. To avoid damage, it recommends using soft cups, without fiber coating. After washing, wipe the film dry with a cotton cloth or paper napkins. Do not accumulate condensation on the glass.

Power connections require maximum attention. Periodically check the condition of the electrical system

Is it possible to do electrical tinting with your own hands?

Important! Self-installation of pdlc smart film is unrealistic. Firstly, it is extremely difficult to find a finished product that will fit a particular car model. Glasses must order from the manufacturer or its dealer. Secondly, it will not be possible to cut glass with high quality, because.

The end seal of the product will reveal. Moisture can freely enter the interlayer space and accumulate there. Finally, it is very difficult to securely fasten the contacts with your own hands.

Do-it-yourself pdlc smart film is quite simple to stick with your own hands. Such tinting, in principle, can be done independently, observing extreme caution.

Work is carried out in the following order

1. The dimensions of the glass are carefully measure.
2. The film is cut out without removing the protective layer, according to the principle: the measure size plus 1 cm in each direction.
3. The surface of thepdlc smart film is being prepared – cleaning from dust and dirt. Grease stains are especially carefully eliminated.
4. Carefully remove the protective coating. The film glue to the glass from the inside of the car. It gently smooth out with a rubber spatula. There should be no air bubbles under the film.

Thus, tinting with pdlc smart film can be done by hand, but you should think about the appropriateness of such an event. Smart film is an expensive material. Poor quality of its gluing can lead to its rapid failure. There is a significant risk of financial loss.

What is protective smart film?

The thresholds of the car are daily exposed to the destructive effects of the shoes of the driver and passengers. Gravel and sand flying off from under the wheels. In addition to the negative impact of the environment in general. Protective smart film PDLC for car thresholds will be an excellent solution for solving such a situation.

Roads are far from ideal, which also leads to damage to the car, forcing drivers to think about ways to keep the car intact. Over time, the paint on the door sills can wear down to the metal, ruining the look of the car. It can also lead to more serious damage, such as metal corrosion.

Why you should choose anti-gravel film for threshold protection?

The best choice for such protection is the anti-gravel film. It is transparent, elastic and durable. The smart film PDLC is usually thick enough to reliably protect the paint surface from damage.

Due to its absolute transparency, the film does not change the color of the car. It also transmits ultraviolet color. So, there will no difference between the parts pasted over with the film or without it.

A reliable protection for your car

The film for thresholds of a car is imperceptible on a surface, but at the same time it will be a reliable protection for your car. To protect the car, you should choose a thick film, because the thicker the film, the more reliable the protection.

The thickness of the smart film PDLC depends on its layering – the more layers, the thicker and more reliable the film. With the help of an anti-gravel film, the outer sills also protect. Which are also significantly damaged during the operation of the car.

Film can fit any threshold shape: high elasticity

Films for car sills can glue both with the help of ready-made patterns, and in a single piece. From which the desired shape is then cut out. Due to its high elasticity, the polyurethane film will fit any threshold shape.

Smart film PDLC is best for wrapping car sills, as it is thicker and will protect your car better and longer. If you install anti-gravel protection on your car. You will not have to worry about damage from shoes, stones accidentally flying out from under the wheels, etc. for a long time.

No traces of glue and does not damage the car paintwork

The film for car sills does not peel off, does not turn yellow and does not fade.

The advantages of a protective film are:

• Protection of thresholds from scratches, chips and scuffs;
• No traces after removal;
• 100% transparency and invisibility on the car;
• Lack of complex special care;
• Prevention of corrosion due to moisture ingress;
• Protection of a paint and varnish covering from gasoline, oils, chemicals.

If you choose a smart film PDLC for car sills, you will soon forget that it pastes. But at the same time, you will be glad to see a whole and undamaged factory coating if you decide to remove the film. You can stick the film by contacting specialized service centers, or on your own by buying a pattern for your car, or a piece of film.

How to apply protective film?

In order to stick a protective film, you must follow some rules.

1. First of all, decide on the surface on which the film will paste. Inside, you can stick the area that damage, and to protect the outer thresholds of the car. Glue the smart film PDLC completely on the entire surface in order to protect the paintwork from gravel;
2. Next, you need to thoroughly wash and dry the thresholds, removing all dirt and sand. There should be no foreign elements on the surface, otherwise the film will peel off or collapse in this place;
3. Next, you need to degrease the surface, using special chemicals or alcohol, and also dry it;
4. Now you can start gluing the film. It is better to do it with the help of special tools to get rid of all possible air bubbles under the film.
   

In any case, car sill protection smart film PDLC is not as easy to stick as it might seem at first glance, so you’d better turn to professionals who will do it quickly and efficiently, and you won’t have to worry about possible mistakes and wasted money.

High protective ability, high transparency and long service life

For plastic car sills, the film can also be easily pasted, since the anti-gravel film adheres well to any surface.  Each has its own distinctive characteristics, but all are distinguished by high protective ability, high transparency and long service life. At the same time, the service life of the smart film PDLC from the China brand WGLASS can reach up to 10 years.

We guarantee the originality and quality of each film

In our online store you can choose the film that suits you and find ready-made patterns. We work directly with suppliers, and therefore we guarantee the originality and quality of each film. If you have any questions, our consultants are ready to answer them, and you can contact them by calling or writing in the online chat on the website.

You can also buy a film to protect the thresholds on the website using the online chat, order form or with the support of our consultants.

Roof protection with anti-gravel smart film PDLC

Car roof film can be a great solution to this problem. The roof of the car is easy to protect with both a transparent anti-gravel film and a colored vinyl film. Anti-gravel film will be a reliable protection for your car, and vinyl film will help decorate the exterior.

Car roof films: protection from hail, rain

The polyurethane film absorbs and spreads the impact force over the entire surface of the film, which helps to avoid damage to the car. The film reliably protects the car from hail, rain, branches and other possible damage.

The smart film PDLC can be easy to replace with a new one

Protecting the roof of a car with a film is a good and more profitable option, since repainting the roof of a car after damage will be much more expensive and time consuming. Also, if necessary, the film is easy to replace with a new one, since the film does not damage the factory paintwork and does not leave marks on it.

In addition, the film transmits ultraviolet rays, which allows the details to not differ in tone, regardless of whether they are pasted over or not. Anti-gravel smart film PDLC is glossy or matte, and the thickness of the film is sufficient to provide the car with reliable protection.

Vinyl roof wrap: a wide variety of colors and textures

Car roof protection can also look original, since vinyl films can be good for gluing, which come in a wide variety of colors and textures. Vinyl films provide less protection than anti-gravel foams, however, they will still protect against light damage.

Vinyl films protect the car coating from fading

The lifespan of a vinyl film is less than that of an anti-gravel film, but it can be beneficial for those who like to change the look of their car frequently. Smart film PDLC protect the car coating from fading well, since they practically do not transmit ultraviolet light.

Smart film manufacturer is becoming more and more popular every day. Film tinting can be both one of the elements of automotive decor, and protection of headlights from damage, weather conditions. Tinted both front and rear lights. Tinted headlights with a film create an original car design.

The choice of the film will not be difficult

If you choose a film in the color of the car’s paintwork, and since the colors of the films are now very diverse. The choice of the film will not be difficult.

One of the ways to tint is to tint the optics using a smart film manufacturer that design specifically for this purpose. These are films from the WGLASS and Smart brands.

According to safety requirements, tinting should not interfere with the uniform transmission of light. It also meets the necessary parameters of brightness, range and area of ​​illumination. These parameters must be strictly adhered to in order to avoid getting into dangerous situations.

Benefits of car window tinting

Film for car optics has many advantages compared to painting headlights. For example, the film is easily applied and effortlessly removed if necessary. The film has a uniform color, which will not interfere with light transmission and will not distort it.

In addition, smart film manufacturer acts as a protection for the headlights from minor damage, from haze and fading. With the help of tinted headlights, you can easily and quickly transform the car, highlighting it among the flow of other cars.

Films for tinting optics

You can tint the rear lights with a film in the same way as the front ones. However, without forgetting the need to adhere to the permissible light transmission standards.

The film for tinting optics from the Smart brand has a high optical transparency, and also stretches well, which makes it possible to paste over headlights of any shape with it and does not visually distort objects. Smart film manufacturer of this brand allows you to tint the headlights in a variety of gray shades.

Smart Blacklight is a film specially designed to protect optics from damage caused by gravel, insects and cleaning brushes. Glossy light gray film will help to create a unique car design.

Films for tinting car optics WGLASS

These have a uniform texture, which eliminates the distortion of light transmission. This film has excellent light transmission and does not impair the visibility of brake lights even in bright sunlight. The film is very elastic.

This makes it possible to paste even optics with a complex curved surface, and a strong adhesive layer ensures excellent adhesion and long-term operation of the smart film manufacturer without peeling off the edges. WGLASS film is available in a wide variety of colors – yellow, red, green and many more – allowing you to match the film to any car color if the need arises.

Films for tinting optics with a film

In case of significant damage or at the end of its service life, the film is easy to remove from the optics without damaging the surface and leaving no traces of glue; if necessary, the film is easy to polish if you choose a high-quality film. Our online store works directly with suppliers, and therefore we can guarantee the originality and quality of each roll of smart film manufacturer.

Caring for tinted optics

Caring for tinted headlights is just as important as caring for the rest of your car. Only the first time after gluing should be careful. Subsequently, direct strong pressure from the washing equipment or its incorrect inclination is easy to avoid in order avoiding peeling off the film at the edges.

You should also refrain from using alkaline and abrasive detergents and do not rub the surface covered with a film too hard. Also, if possible, solvents, gasoline and other harsh chemicals should avoid. We can remove it as soon as possible with microfiber or a soft cloth dampened with water.

Smart film manufacturer will not be burdensome for you

Caring for tinted optics will not be burdensome for you, especially considering all the benefits of protecting headlights with a film. In order to tint the headlights with a film, you should contact the professionals in the studio.

Usually the process takes only a few hours, but you will be sure that the work comes with high quality. The film will not peel off and will serve you for many years. For tinting headlights with film, special patterns are also there.  This will allow you to choose the film immediately for the headlights of your car without the need to cut the smart film manufacturer additionally.

It is possible to tint the headlights with film yourself if you have enough experience and are ready for the possible risks of improper gluing.

Caring for tinted smart film

To do this, you will also need a lot of different tools. You need a room there will be the perfect temperature, there will be no draft, dust and dirt. It is not worth the risk and it is better to immediately turn to the masters.  They will quickly transform the headlights of the car, taking into account any of your wishes.

Smart film manufacturer elements are quite expensive. Stones and gravel can cause cracks in the headlights, through which dust, dirt and moisture can enter. This greatly impairs the dispersion of light and makes movement difficult. Also, over time, the plastic of the headlights can become cloudy, which also impairs visibility.

 

Provide protection from minor damage and fogging

Film tinting will protect your headlights from minor damage and fogging, which will allow you to clearly see the road, pedestrians and other road users.

You can use a matte anti-gravel film;

For the best protection of headlights from damage, an anti-gravel smart film manufacturer is used, which will reliably protect the optics from gravel, sand, stones, ice, chips and scratches. However, the anti-gravel film is transparent, and it will not work to tint the headlights with it, except to add some glossiness.

You can use a matte anti-gravel film; with its help you can add a little variety without being afraid of the level of lighting. Tinting headlights, both front and rear, subject to all standards, is allowed.

Many people may think of a protective sheet for smartphones when they hear the word “glass film”, but this time the spotlight is the smart film for windows.

Windows are indispensable for taking in light and outside air into a house, but they are also a place of trouble such as being worried about the line of sight from the outside and breaking glass causing a secondary disaster in the event of a disaster.

Glass film is effective for windows

Glass film is also effective for windows with gum tape or curing tape stuck to it, which is seen when a large typhoon is approaching.

Smart film for windows is an excellent item that enhances the quality of our lives with various functions, contrary to its thin appearance, such as blindfolding from the outside, prevention of glass shattering, UV protection, and interior arrangement.

However, there are probably few people who have actually pasted the glass film on their own. There are two types of glass film.

Can peel off cleanly and reattach

that can be thinly and firmly attached, and the “adsorption type” that can peel off cleanly and reattach. It is an item that you can paste yourself.

This page introduces the features of smart film for windows, and in the latter half, spotlight the “adhesive type” glass film, which tends to concern that it cannot peel off once it pastes, and after detailed pasting and peeling. What is the surface of the window? I will also challenge the mystery.

Live a bright life without closing the curtain

 

In a residential area with condominiums and detached houses, it is not uncommon to find a house right next to you outside the window. I think there are many people who worry about people’s eyes and live with the curtains closed.

A glass film with a blindfold effect is recommended

Mosaic type frosted glass type smart film for windows takes in light and blocks people’s eyes, so you don’t have to close the curtain completely!

For disaster countermeasures for windows and glass interiors

One of the dangers in the event of a disaster injuries cause by scattered glass. If you attach a glass film, you can prevent the glass from scattering when it breaks, so you can reduce secondary disasters!

It recommends to attach it to the glass part of the interior such as a cupboard as a safety measure in the room.

Smart film for windows shields heat rays to save energy

Windows are not only light and outside air, but also heat entrances. By attaching a heat-shielding type glass film to the window glass, you can expect the energy-saving effect of the air conditioner by preventing heat rays from the outside in the summer.

Protects skin and furniture from sunburn

Many people concern about sunburn on their skin due to the UV rays that enter through the windows, but people are not the only ones who get sunburn. It also has adverse effects such as fading and deterioration of strength on furniture and floors.

In recent years, solid wood furniture and flooring that make the best use of the material as it is are also popular, but unprocessed materials are more susceptible to light and temperature changes, so I would like to take measures. A smart film for windows with a UV blocking effect will block most of the UV rays.

“Insect repellent” effect | Makes it difficult to attract insects

The glass film with UV blocking effect also has the effect of reducing phototactic insects that collect in ultraviolet rays. If you worry about insects gathering on the windowsill, please try it.

Glass film is recommended for such places!

In the window of the room

As a UV measure for windows that receive a lot of sunlight. In addition, it is effective as a secondary disaster countermeasure to take measures to prevent scattering around the bedroom and windows near the evacuation route in case of emergency.

Around the bathroom

Another place with high demand of smart film for windows

Even if you have a good view in such a place, it’s just embarrassing … You can rest assured that you can take measures against blindfolding!

For interior arrangements

If you don’t want to see what’s inside, such as a cupboard or cupboard, we recommend arranging it with glass film. You can hide the inside by just sticking a little pattern. Two birds with one stone that also prevent scattering.

In the shop window

It’s hard to find in a general house, but it’s also recommended for reinforcing the shop window of a store. Smart film for windows also helps prevent sunburn on display products and helps the safety of those around us in the event of a disaster.

I don’t want insects to ruin my display! There seems to be some shops that construct for the purpose of repelling insects.

“Pattern” and effect of glass film

The common effect of sticking a glass film on the entire window is “prevention of scattering”. Other than that, there is a big difference depending on the pattern.

Let’s see the difference in the effect depending on the pattern!

Transparent type: Does not spoil the appearance of the window glass!

This transparent type does not block the view and does not spoil the appearance of the original glass window. UV cut effect is also nice!

Mirror type: Reduces glare & blocks the view from the outside

The characteristic of the mirror type smart film for windows is that it blocks the view from the outside and looks clear from the inside. The windows of high-rise buildings often look like glittering reflections. That is the so-called mirror type window! It is an excellent item that provides both privacy and visibility.

However, the feature is that the film is easier to see through at night than during the day. Glittering light reflections can be a problem in your neighborhood. You may need to be careful where you use it.

Design type: For window accents

The “design type” is recommended for decorating windowpanes. How about smart film glass that suits your room with various patterns such as stripes, floral patterns, and stained glass? Recommended for small interior arrangements such as glass doors in cupboards. It can also use as an indoor disaster countermeasure.

Summary of adhesive type features

Since it can firmly attach, the effect of preventing scattering is higher than that of the adsorption type. After the adhesive has dried, it cannot reapply.

There are many functions and types.

• The film is thin and the finish is natural.
• Summary of features of adsorption type
• Smart film glassdoesn’t use adhesive, so it can easily remove.
• Recommended for rent as it can peel off cleanly.
• You can re-paste as many times as you like.
• Installation is easier than the adhesive type.

Adhesive type / adsorption type | Common precautions

Construction is not possible when the outside temperature is below 0 degrees. (Moisture sprayed on the base during construction freezes and causes poor adhesion.)

Glass that can be pasted, glass that cannot be pasted

Although there are differences in adhesive strength depending on the type of glass film, it is basically possible to attach glass with a smooth and smooth surface.

A special smart film glass with an internal structure

 

The table below is a general guide. It may differ from the actual product depending on the condition of the window glass and the product, so it recommend to check the product details at the time of purchase, and if you worry, try pasting using a sample etc. in advance.

A glass film that blindfolds from the outside, prevents scattering in case of emergency, and blocks UV rays that are of concern depending on the product.

Nowadays, more and more people are sticking it not only on windows but also on cupboards and small DIY accessories.

I want to put such a smart film glass in earnest! This is a must-see for those who want to paste it more beautifully. It will take a little more work, but we promise that you will be able to put it on beautifully!

Preparation before pasting

Spread a curing sheet to keep the surrounding area clean.

Place a curing sheet to keep the floor clean. Be sure to cure the carpet, especially if the bottom is a carpet, or if there is a problem with water such as electrical appliances. If you don’t need a bath towel, lay it on the floor and it will absorb the dripping water.

Make an aqueous solution and clean the smart film glass

• Put 2-3% of neutral detergent in a spray bottle, dilute it with water, and spray it on the glass.
• Use a glass scraper to remove dirt (dust and tar) that has stuck to the glass.
• The glass will damage, so don’t put too much force on it!
• At first, you will hear a “crisp” sound, but as the dirt remove, “Sue” and the glass scraper will pass through.
• Be sure to clean it with a clean blade.
• If the window is very dirty, clean it carefully.
• Start by rubbing from the middle of the glass and later rubbing the edges. Rub the glass scraper first in the black direction of the figure and then in the red direction.
• Spray the smart film glasswith an aqueous solution once more, and then drain the water with a squeegee.
• If it doesn’t look good after doing this, repeat the same thing a couple of times.
• Finally, wipe the window (near the rubber) clean with a kitchen towel. If you do not do this, you will inhale dirty water and the glass film will come off.
• Now the glass is clean and the film is ready to stick.

Cut the glass film

• First, measure the vertical and horizontal sizes of the window.
• Mark the glass film with a size slightly larger than the window size (about 3 cm to 5 cm).
• Cut the smart film glassfilm with a cutter.
• Be careful not to make wrinkles or creases when cutting.
• Be sure to cut it in a flat and clean place.
• Stick a glass film

Spray the glass with an aqueous solution

Put a large amount of aqueous solution spray on the glass to form a film of aqueous solution. If the amount of aqueous solution is low, the glass film will stick to the glass immediately when it applies, making it difficult to apply.

Spray the aqueous solution on the back of the film

While peeling off the backing paper of the smart film glass, spray the aqueous solution on the back of the film. If the backing paper is difficult to peel off, attach cellophane tape to the corners of the backing paper and peel it off.

Speed ​​is the key to this task.

If it is slow, the static electricity generated when the backing paper peel off will cause dust in the air to adhere to the adhesive layer, and after the film attach, it will become like dust particles and will be difficult to remove.

It is more reliable to install this smart film glass with two people and there is no failure.

Paste the film.

Gently hold both ends of the top of the glass film with your hands and stick it. At that time, align the edge with the side with the key of the window, and paste it with a gap of about 2 mm from around the window frame.

Align the gaps evenly from top to bottom

Once the position is determined, spray the aqueous solution over the entire surface of the film, and use a squeegee to drain the aqueous solution and air to make a temporary press.

• When using a squeegee, be sure to spray an aqueous solution. Otherwise, the smart film glasswill be scratched.
• While holding the glass film with one hand so that it does not shift, remove it.
• When removing the rough surface, move the squeegee from the inside to the outside.

Use a cutter to Cut excess film

• Cut the remaining excess glass film with a cutter.
• Cut around the glass frame and the edge of the film so that there is a gap of about 2 mm.
• Be sure to cut the inside by about 2 mm to drain water. Cut with a cutter using a
• cutter guide or a transparent ruler.

What is intelligent film?

Smart film intelligent helps to keep the temperature inside the car at a stable level. This helps to keep the car’s air conditioner from running at full capacity, helping to save fuel for your car.

The country is developing more and more, leading to an increasing demand for car use. Especially, in big cities, population density as well as industrial activities taking place more and more. in the humid tropics, sunny all year round. The weather is hotter than the rest of the area.

Is it necessary to paste smart film intelligent?

People’s demand for using cars is mainly to move faster, more conveniently. It also to avoid the harsh heat from the sun as well as the absorption of heat from the environment.

But it’s hard to sit in a car and it’s still hot, still can’t run away from the sun. Many drivers have come up with solutions for themselves such as: using sunshades, installing more curtains or covering the glass doors with large objects. But it is only a temporary method and does not bring the expected heat protection effect.

The great influence of UV and Infrared rays on humans

According to research, in sunlight there are 3 main radiations: UV rays (4% – 7%), Infrared rays (about 54%), the rest is visible light. In particular, UV and Infrared rays have a great influence on humans.

Understanding the psychology of users, through research and research, the manufacturer has launched effective heat-resistant insulating smart film intelligent. It is more suitable to the needs of users.

What is intelligent film, and its parameters?

Intelligent film is made up of many layers of polyester plastic film. Each layer is integrated with coating of ultra-thin intelligent materials such as carbon, ceramic enamel or other materials. The final layer is an extremely thin and transparent adhesive layer that forms a filter for the spectral ranges. Used to paste the inside of car windows, buildings.

Some outstanding uses of most intelligent films

Anti-heat and stabilize the temperature in the car: Thanks to its ability to reflect light as well as absorb heat on the surface. Smart film intelligent does a great job of reducing the heat from the environment as well as keeping the most appropriate heat balance in the car.

Protect health and furniture:

It can block a large amount of sunlight and especially ultraviolet and infrared rays, it has the ability to reduce harmful effects to human health such as:  reduce skin and eye diseases compared to facing directly.

Kindness of the work for film

The furniture in the car is mostly made of plastic, which is very resistant to the sun. With its outstanding advantages, insulating film can help: reduce the level of discoloration and damage such as: cracking, blistering, heavier than detail deformation. Smart film intelligent helps maintain the beauty and durability of car interior details.

Reducing glare, supporting safe driving:

Insulating film has a certain ability to reduce glare, helping the driver to reduce glare when seeing, especially when the car is facing the sun or when running at night, encountering problems. headlights from oncoming vehicles. From there, it helps to improve visibility and safe driving.

Increase safety for vehicle operation:

Safety when broken glass, threatening human life. Film supports protection as a safety net, keeping broken glass together, avoiding glass fragments splashing on car occupants.

Helps to balance the temperature in the car

Instead of having to turn on the air conditioner continuously with high frequency and capacity when the temperature in the car is high, now the smart film intelligent helps to balance the temperature in the car, the air conditioner does not need to work with frequency, high power again. Helps save more fuel for cars as well as costs for users.

High security with one-way vision, people sitting inside can see the outside very clearly but outside will not see, increasing privacy, more discreet for users and the interior.

Notes when choosing intelligent film:

The first is the technical specifications of the car, as I have shared above:

• Ultraviolet (UV) rejection,
• Infrared (IR) rejection,
• Light transmission rate (VLT),
• Reflection rate. light (VLR).

The ability to absorb heat

The origin is clear; you should learn carefully about the types of smart film intelligent available on the market. If possible, ask for more advice from professional car care centers. Avoid buying cheap or unknown origin and then losing money unjustly.

Choose the type of film you like, the color and the price

Should I paste the film myself at home, will the intelligent film damage the glass?

If you already know how the process is done, then just buy a stable film and importantly, the tools to serve the film must ensure quality and correct effect for each process.

The process of implementation: try not to make mistakes

If you are not sure or do not fully understand the smart film intelligent, it is best to bring it to professional car care centers, where they have a team of highly skilled technicians combined with equipment. Specialized tools and many years of experience in this field will help answer your questions and ensure the safety of your pet.

In addition, automotive and window films have different compositions, manufacturing technology, dimensions, installation principles and other significant nuances.

What is interesting about architectural self-adhesive film

This is how professionals call the category of tinting materials intended for installation exclusively on translucent elements of buildings!

Architectural window film: what is it?

In short, this is a self-adhesive smart film intelligent on the glass of a window / balcony / showcase and similar parts of a residential or commercial (social, administrative) property. Therefore, the epithet “architectural” is used to immediately indicate the target affiliation of the material.

As with car tinting, sticking a self-adhesive film on windows, balcony blocks and entrance groups is needed both for beauty and for certain advantages.

Conclusion

The most banal is achieving a certain degree of privacy. And if with car films the driver’s imagination is restrained by clear legal norms, then in the case of smart film intelligent there are no restrictions! The main thing is that the material is of high quality.

How to properly stick the film on a car?

More and more car owners these days know what car film is. With the help of the smart film, you can easily transform the appearance of your car, making it more unique, or reliably protect it from various damages if you use polyurethane film.

With the help of privacy film, you can easily change the color of the car, both completely and partially, you can use various inscriptions or drawings, or you can create your own unique design, which will definitely be absolutely exclusive.

Anti-gravel smart film will help you keep the paintwork and optics of the car in their original form for a long time, as it will protect against scratches, chips, abrasions, negative environmental influences, etc.

Sticking a tint film on a car allows you to protect the interior from the negative effects of ultraviolet and infrared rays, as well as achieve some confidentiality. Among other things, the smart film on the glass keeps the fragments on the adhesive layer, in case of damage, preventing them from scattering.

Anti-gravel and privacy wrapping

Covering the body with polyurethane smart film requires experience and skill, since only properly installed armor will protect your car for many years. It is very difficult to properly cover the car with foil yourself, because this requires a lot of different tools, and, again, experience.

The workshops have the necessary tools for pasting with anti-gravel films, such as building hair dryers, squeegees, forcing, etc., in addition, the masters will give you precise and detailed advice on pasting.

In order to properly install the smart film, you must have a sufficient number of different tools:

• distillation;
• soap solution and spray;
• rubber spatula;
• stationery knife;
• technical hair dryer;
• microfiber or soft towels;
• a ruler and more.

Installation of smart film

Privacy or polyurethane films are glued using the so-called “wet” method, that is, a soap solution is good to install the film.

First of all, in order to apply the smart film, the car must be clean of all contaminants.

Next, you need to moisten the paintwork and the film with soapy water, after removing the protective backing from the film. After that, the film should come on the surface, carefully straightening the creases.

It is necessary to work from the center to the edges, pressing the distillation firmly against the film to remove all residual air and soap solution. If necessary, use a hair dryer to make the film softer and more pliable.

Next, you need to cut off the excess film with a clerical knife and gently wipe the film with microfiber.

Pasting with carbon smart film

Carbon film has both positive and negative sides. A film with an imitation of a carbon surface is much cheaper than real carbon, which is a significant plus. Such a film can be glued to almost any surface, be it metal, pre-prepared plastic or glass surface.

With the help of the film, you can hide minor surface damage, such as scuffs, scratches or small chips.

Also, this film will protect the pasted surface from fading, since it does not transmit ultraviolet rays, additionally protecting the paintwork from the effects of gasoline, chemicals and pollution.

The technology for pasting the smart film is different from the previous one. The carbon film glues “dry” using a squeegee and a hair dryer.

It is necessary to press the film to the surface with a squeegee, starting from the center to the edges. Next, using a hair dryer, you need to heat the smart film, thus activating the glue and its adhesion to the surface of the car.

After heating, it is necessary to smooth out the film again with a squeegee in order to get rid of possible air bubbles under the film. It is good not to wash a car covered with a film for at least 5 days, so as not to subject the film to pressure from washing units.

Pasting car headlights with foil

Headlights need reliable protection as they are one of the most vulnerable parts of a car. Protective smart film for car headlights protects them from damage, as well as preserves their transparency and avoids expensive optics polishing.

The film for car headlights, which will give the best protection, is an anti-gravel polyurethane film. It transmits light as much as possible, and also has absolute transparency.

Use a colored tinted film. 

The process of pasting headlights with smart film is the same as pasting a body with anti-gravel or privacy film. After pasting, the film needs time to dry completely, which depends on the season, temperature, as well as the room where the machine is located.

The car can be good almost immediately after installing the film. However, washing should be abandoned for a while.

Features for pasting a car with smart film

Stylish design, affordable price, protective properties are some of the few reasons why many people use films for wrapping their cars.

One of the most important roles in how long the film will last is how it applies correctly. It is difficult to cope with the pasting on your own. There is always the possibility of damaging either the film itself or the paintwork.

Improper adhesion of privacy film can lead to an untidy appearance of the car, damage and corrosion to the paintwork, as well as waste of extra money on correcting errors. It is always good to contact a professional gluer who has experience, knowledge, all the necessary conditions and tools for working with smart film.

There are some nuances that you should definitely take into account when working with film, if you nevertheless decide to take up pasting yourself.

The surface on which the privacy or anti-gravel film will glue must be clean and dry.

Pasting with film should be done with folds, both for anti-gravel and privacy films. This will avoid peeling off the film at the edges.

Smart film care after pasting

First of all, these are car washes. Always warn service workers that your car covers with plastic. The wrong angle or too strong pressure of water can touch and tear off the edge of the film.

It is always worthwhile to remove various contaminants from the surface of the smart film in a timely manner, since although most of them have short-term resistance to them, prolonged exposure can damage the film.

Styling and tuning of cars these days does not lose its relevance, many motorists are trying to change the appearance of their car or add any details.

Carbon fiber material has an attractive appearance, excellent technical characteristics and therefore is often used for the manufacture of car parts. However, the price of such material is quite high, so not every car owner can afford to replace parts with smart ones. In this case, you can use a smart film factory. Of course, it will not lighten the detail, but it will help to achieve an attractive appearance.

Most often you can find a 3D film with a smart look. It has a three-dimensional pattern and simulates the relief well, in contrast to the 2D smart film. 4D smart films has an even more complex texture, which is almost identical to natural smart fiber, but difficult to manufacture, therefore it is less common and costs a little more.

Advantages and disadvantages of smart film factory

Film for 3D smart, like any other vinyl film, has its advantages and disadvantages.

• Carbon imitation film is much cheaper than real smart;
• Such a film adheres perfectly to almost any surface, be it metal or plastic;
• Due to its thickness, vinyl film with a smart look will help hide small chips, scratches and scuffs on the car’s paintwork;
• The smart-like film will also protect the paintwork from fading, since it does not transmit ultraviolet rays;
• In case of damage, in smart film factory itcan be easily replaced in whole or in part, in addition, due to the pattern and texture, the joints will not be visible on the surface;
• Smart film has short-term resistance to various types of dirt, oils and gasoline.

Pasting of Carbon Films

Carbon film looks good with different types of pasting, both partial, for example, the hood, mirrors, roof, etc., and full. If you get tired of this type of tuning, the film is easy to remove. It does not damage the surface and does not leave glue traces on it.

However, smart-look vinyl has its drawbacks. One of them is the rather high cost of some brands of film. Also, no matter how high-quality the film is, there is still a need to change it, since the service life of such a film is about 5 years. When pasting with smart film factory, some skill is required, so you should entrust this process to professionals.

When visiting a car wash, you should always warn workers about the presence of a vinyl covering, since an incorrectly selected angle and water pressure can damage the film, peel its edges from the surface, etc.

How to properly glue the smart film in smart film factory?

In order to paste over a car with a smart-like film, you need to have experience in car wrapping and some inventory, so you should always give preference to pasting from professionals.

It is necessary to glue the 3d film for a car in compliance with all the rules so as not to spoil the material or stick the film incorrectly, and subsequently not to receive additional costs for pasting again from professionals.

The correct method for applying the smart film in smart film factory is considered to be the dry method using a squeegee and a hair dryer.

For pasting a smart film, you need tools such as:

• degreaser (isopropyl alcohol);
• soap solution;
• construction hair dryer;
• squeegee;
• a knife for cutting off excess film;
• microfiber

 

The work itself must be carried out in a clean, dry and well-ventilated area in smart film factory. The very surface of the car or the part to be pasted must be well washed and degreased. After pasting, the car must dry for a while for the film to finally adhere to the surface.

Film wrapping around cars is becoming more common these days. It is an excellent and more economical alternative to staining. Film wrapping is much faster than painting, and in addition, it can always be removed or replaced with another. There are many types of vinyl, its textures, colors, brands.

Film wrapping in smart film factory

Film wrapping can be done in various variations, allowing you to create original looks for cars. Often, individual body parts are pasted over with film, allowing you to create a unique car style.

smart films produced from polyvinyl chloride (PVC), by casting or calendaring. For cast film, the material is poured into the required shape, and for calendared film it is rolled out between special rolls.

In Smart film factory, smart film primarily serves as a decorative function. It can only protect the paintwork from fading and minor damage, such as sand ingress.

In addition to being used in the smart film factory, vinyl is also used for print applications such as advertising or clothing printing, for architectural applications such as indoor windows. film films are also in demand in interior decoration.

Types of vinyl films for a car

There is a huge variety of vinyl wraps for car wrapping. In smart film factory films can be either completely transparent or have a certain color, they can be matte or glossy, imitate the texture of leather, wood, smart fiber, metal, etc., which will allow you to achieve a variety of design solutions.

Films have a wide palette of various colors. However, such films are designed to serve as a decorative function. Decorative smart film will help decorate and upgrade your vehicle, but will not protect it from damage in the same way as polyurethane sheeting. Therefore, if you want to protect your car, then you should give preference to polyurethane.

One of the main criteria by which vinyl films are distinguished is the surface texture.

In smart film factory Film is available in a variety of colors and textures. For example, the film can be matte, glossy, textured, camouflage and more. Also, vinyl films can be of different thicknesses, thanks to which they better, for example, hide flaws on the surface.

Glossy film

Glossy vinyl is the most common material that will allow you to quickly and easily change the look of your car without painting. Film wrap on your car will help change the color of your vehicle without the need for expensive paint jobs. This film has characteristics such as:

• resistance to high temperatures;
• wear resistance;
• resistance to chemicals, oils, fuels;
• resistance to ultraviolet rays.

The most popular vinyl colors are black red, blue and gray. Motorists often use black film to imitate a panoramic roof and for “anti-chrome” – pasting chrome elements on a car body.

Glossy films include, perhaps, chrome-like films (however, matte chrome films are also found). These are films with a mirror effect, difficult to work with, but giving an amazing effect on the car. In smart film factory Chromium is most commonly found in silver and gold.

In addition to a beautiful appearance, it will also provide protection to the car body. It will be able to protect the paintwork from minor scratches, chips and abrasions.

Sunlight enters the room through the windows. Self–adhesive window film makes it light and cozy. Sometimes the light becomes annoying, or in the summer it also heats the room additionally. Also, in addition to the positive aspects, sunlight can contribute to the development of diseases. It can irritate eyesight, furniture and interior items burn out due to ultraviolet radiation.

The same problems can occur in the car’s interior – sunlight heats up the interior, interior elements fade, and the seat upholstery deteriorates.

Self–adhesive window film will be an excellent solution in such matters, and in addition will be a great solution for giving the interior a modern touch.

Types of adhesive window film films

Tinting films for windows vary. Moreover, you need to choose depending on your wishes, as well as the goals that you want to achieve. In architectural tinting, there are sun-protection films with various shades, decorative films of different colors, mirror films.

For tinting car glass, special privacy films, colored tint films, transition films and chameleon films are offered.

Self–adhesive window film is very famous in many countries. It has very good impact on commercial and domestic areas.

Mirror film perfectly protects the premises, especially those on the ground floors, from prying eyes, besides; the building with such windows looks incredibly attractive.

However, specular film only has this effect during the daytime, when the outside light is brighter, and in the evening, the specular effect will disappear.

Sun-protection Tint film

Sun-protection tint film also perfectly protects the room from prying eyes, gives the exterior an attractive appearance and helps maintain a comfortable indoor temperature.

Car self–adhesive window film perform the same function. With their help, it is possible to reduce the temperature in the passenger compartment, protect it from burnout and create the effect of one-way visibility.

The self–adhesive window film also gives you extra protection. If the window is broken, the fragments will not scatter throughout the room or the car interior, and will not injure people, but will remain glued to the adhesive layer of the film. An added bonus is that the film protects the glass itself from minor damage such as scratches.

An Energy Saving Film

Another type of coating is an energy-saving film. In addition to tinting, it performs such an important function as keeping warm inside the room in winter. Like tinting films, it allows only part of the visible light to pass into the room, which allows you to maintain a comfortable temperature in the summer. Such a self–adhesive window film allows you to significantly save on cooling in summer and heating in winter.

There is also a decorative tinting film, which has a wide variety of colors, shades and textures and is glued to interior partitions, to windows between rooms, to doors and, in general, to any glass surfaces. With the help of such a film, you can achieve privacy in a room or change its design.

Window tinting has many advantages, including:

• The film replaces curtains, blinds, curtains, since it limits the penetration of light into the room.
• Protects the room from overheating by blocking out ultraviolet and infrared radiation.
• Will help to update the interior design.
• Helps to save money as the load on the air conditioning system is reduced.
• Mirror film will help achieve a one-sided effect.

 

If you use high quality self–adhesive window film from well-known world manufacturers, then you will notice the effect of gluing such a film immediately. From the inside, the film does not change visibility. The changes will only be noticeable to you for the first few days. However, ultraviolet and infrared rays will no longer enter the room, and therefore cause inconvenience.

Tinted plastic windows also have an anti-glare effect, which makes it comfortable to work at a computer or watch TV.

Self–adhesive window film for windows: How to Glue

In order to glue the tint film on glass, be it windows in an apartment or car windows, you need to have:

• enough skills
• knowledge
• and experience in gluing

Also, in order to properly install the film, you must have a sufficient number of various tools:

• distillation;
• soap solution and spray;
• rubber spatula;
• stationery knife;
• microfiber or soft towels;

Installation of Windows Film

First of all, in order to stick the self–adhesive window film on the window, it must be clean of all dirt. Remove even the smallest remnants of paint, putty or other traces.

Next, you need to moisten the glass and the film with soapy water, after removing the protective backing from the film. Then place the film on the glass, carefully smoothing out the creases.

After self–adhesive window film installs on the glass, moisten it again with soapy water. and, using forcing, starting from the center and towards the edges, smooth the film and get rid of the water under the film.

It is necessary to work from the center to the edges, from top to bottom, pressing the distillation firmly enough to the film in order to get rid of all the remaining soap solution. Next, you need to cut off the excess film with a clerical knife and gently wipe the film with microfiber.

After installation, self–adhesive window film must not touch with hands and washed for the first few days. To care for the film, you do not need any special skills or devices. Windows should be washed with a soft cloth, do not use aggressive and abrasive detergents.

The process of gluing tint film on windows is not as simple as it seems at first glance. In order to avoid additional wasting of time and money on fixing, it is better to immediately contact the professionals who know exactly how to stick the film correctly so that it will serve you for many years.

Self-adhesive window film: Where to Buy

The dimensions of the tint film for windows should not be millimeter to millimeter; it is always worth taking a film with a few centimeters in reserve at the edges. The price of a tint film for windows is fully justified by its characteristics and the comfort it provides.

You can buy self–adhesive window film for windows in glass market at affordable prices, choosing the film that will ideally suit all your needs.